Qsc plx 3402 settings for dbx driverack 260 manual#
Qsc plx 3402 settings for dbx driverack 260 full#
Qsc plx 3402 settings for dbx driverack 260 series#

Qsc plx 3402 settings for dbx driverack 260 full#

BRIDGE MONO MODE This mode combines the full power capabilities of both channels into a single speaker system.ġ4 A U D I O POWER AMPLIFIER PLX 30 32 dB 20 22 24 26 28 I8 I4 8 - 30 32 20 22 24 26 28 dB I8 I4 8 - SIGNAL POWER BRIDGE PARALLEL -20dB -IOdB CLIP 1 C H A N N E L 2 P R O 3 0 0 0 W A T T 3002 3.50' 88.9 mm 12.25' 311.2 mm 13.25' 336.6 mm 17.ġ5 CONNECTIONS OUTPUT CLIP LIMIT ON CLIP LIMIT ON CH 1 P2 CH 2 CH 2 TIP 1/4 XLR INPUT IMPEDANCE: 1 2K BALANCED INPUT PINOUTS INPUT PINOUTS MODE SWITCHES MODE SWITCHES CH 1 CH 2 PINOUT 1+ 1+ 2+ RNG SLV.ġ6 Speakon™ Outputs The PLX amplifier offers a choice of output connections, with two Neutrik NL4MD Speakon jacks and two pairs of 'touchproof' binding posts. 2 input Bridged Mono FEA TURES & SETUP SEE THE ADDITIONAL BRIDGE MONO MODE WARNINGS ON P AGE 11. 2 input P arallel What are the differences among Stereo, Parallel Input, and Bridge Mono modes? STEREO MODE This is the 'normal' way of using the amplifier, in which each channel is fully independent.ġ3 Ch. 2 input Stereo, bi-amp, 2-channel FEA TURES & SETUP Ch. Each channel drives its own speaker load, with independent gain, filtering, and clip limiting.ġ1 FEA TURES & SETUP Bridge mono mode WHA T IT IS Bridged mono mode combines the power of both amp channels into one speaker, resulting in twice the voltage swing, four times the peak power, and approximately three times the sustained power of a single channel.ġ2 Ch. The filter settings for each channel are controlled individually through the DIP switch settings shown.ġ0 Parallel input mode WHA T IT IS The 'Parallel Input' switches let you operate the amplifier in parallel mode, delivering the same signal to both channels without using a Y-cable. This improves bass performance by limiting sub-audio cone motion, making more power available for the speakers' rated frequency range.

The clip limiter detects this and quickly reduces the gain to minimize the amount of overdrive.ĩ Input filter WHA T IT IS The low-frequency (LF) filter rolls off signals below either 30 Hz or 50 Hz. Interruptor de encendido 2.ħ OUTPUT CLIP LIMIT ON CLIP LIMIT ON CH 1 P2 CH 2 CH 2 TIP 1/4 XLR PINOUT INPUT IMPEDANCE: 12K BALANCED INPUT PINOUTS MODE SWITCHES MODE SWITCHES CH 1 CH 2 PINOUT 1+ 1+ 2+ RNG SLV 1- 1- BRIDGE 2- P3 P.Ĩ Clip limiter WHA T IT IS When the audio signal drives the amp's output circuit beyond its power capability, it clips, flattening the peaks of the waveform. POWER, BRIDGE, and PARALLEL indicator LEDs 7.

CLIP, -10 dB, -20 dB and SIGNAL indicator LEDs, both channels 5. These fan- cooled, 2-channel, 2-RU, amps provide unprecedented power in a strong, compact chassis.Ħ Front panel 1. PowerWave TM technology and a refined audio structure combine studio-quality performance with touring-quality portability.

Qsc plx 3402 settings for dbx driverack 260 series#

declares as its sole responsibility that the above named product is in compliance with the Council Directive 89/336/EEC of on the harmon.ĥ INTRODUCTION EINFÜHRUNG INTRODUCCIÓN A V ANT -PROPOS The PLX Series Amplifiers. Ĥ Declaration of Conformity QSC Audio Products, Inc. 21 Amplification d'instrument Instrument-Verstärkung Amplificación de instrumento TROUBLESHOOTING. 20 Sonorisation Beschallung Sonido en vivo Instrument amplification. Diese Spannung ist hoch genug, um Personen durch elektrischen Schlag zu gefährden.ģ Sound reinforcement.

Qsc plx 3402 settings for dbx driverack 260 manual#

C User Manual Manuel de l’utilisateur Bedienhandbuch Manual del Usuario *TD-000072-00*.Ģ Erklärung der Bildsymbole Das Blitzzeichen innerhalb eines gleichseitigen Dreiecks warnt den Benutzer vor nicht isolierter, gefährlicher Spannung im Inneren des Gerätes.